(Contact factory for information on models
with bi-directional flow capability or velocities in excess of above specifications.)
Materials
Sensor: Fiberglass
Cable: Polyurethane outer jacket
Insertion Hardware: 316 Stainless Steel exposed to flow.
Compression Seal: Silicone Rubber
Sensor Electrodes: Carbon
Number of electrodes varies with sensor length.
Transmitter Enclosure
NEMA 4X/IP65. Separate termination and
electronics compartments. Glass filled polypropylene with clear
polycarbonate window.
Transmitter-Dimensions
8.4"H x 6.4"W x 2.8"D
(214mm x 163 mm x 70 mm)
Transmitter-Weight
3.2 lbs. (1.5kg)
Potable Water Applications
Suitable for use in contact with potable water. Water Byelaws Scheme (WBS)
Approved Product. Meets BS6920 - Cert. # 9706516
Configuration and Set-Up
Programming can be easily done on site using the keypad. Two levels of
user defined password protection are provided.
Outputs
Dual Alarms
(2 separate outputs): Isolated protected transistor switch capable of
sinking <250mA @ <35V. Note: Not isolated from frequency output.
Fully programmable for high/low flow rates. % of range, empty-pipe,
fault conditions, forward/reverse, polarity (normally open/close),
analog over-range, pulse over-range, pulse cutoff, etc .
Environmental
Pressure/Temperature Limits:
Sensor: Flow Temperature Range
32° to 110°F (0° to 44°C) @ 250 psi - Standard
32° to 140°F (0° to 60°C) @ 250 psi - Optional
Electronics: Temperature limits
Operating: -14° to 140°F (-25° to +60°C)
Storage: 5° to 167°F (-15°C to +75°C)
Electrical Connections
0.5 inch NPT with gasket seal
Keypad and Display
Can be used to access and change all set-up parameters using four
membrane keys and 3-line display.
3-Line, 16 character, backlit LCD display with large 1/2"
numerals for flow rate and two lines for engineering units, totalizers,
alarm status, velocity and percent of range.
Isolation
Galvanic separation to 50VDC between analog, pulse/alarm, and
earth/ground.
Electrical Safety
Meets ANSI/ISA-S82.10-1988 and S82.03-1988
Power Supply
Universal switch mode.
AC: 85 to 265V 45 to 400 Hz at 20VA max. or DC: 11 to 40V at 20VA max.
AC or DC must be specified at time of ordering.
Vibration Specification
Meets BS2011: Part 2.1Fc: 1983
Internal Totalizer
9-digit totalizer. Can be programmed to reset via external input or
the keypad. Reset from keypad can be password protected.
Test Mode and Output Circuit Loop
Verification
After transmitter has been programmed, operation of the test mode will
drive all outputs to a programmed value which provides a total system
test.
Ordering Information
Multi-Mag™ flowmeter includes modified NEMA 4X/IP65
(separate termination and electronics compartment) glass filled
polypropylene electronics enclosure with polycarbonate window,
electromagnetic velocity sensor with 20' cable, 4 membrane keys for
configuring the transmitter, 3-line LCD backlit display with one line
of 5-1/2" numerals for flow rate indication and 2 lines
containing 16 characters for viewing engineering units, velocity,
totalizer, alarm status and flow rate expressed as a percent of full
scale, one flow proportional or frequency output (transistor type) for
flow rate or for external totalize, a 4-20 mA output for flow and one
instruction manual.
Options include high temperature sensor, extended sensor
cable, (Maximum length 500' (152 m)), pole mounting kit, insertion tool,
sun shield, and additional instruction manuals.
Contact factory for Sensor Mounting Hardware
Ordering Information
